Portal axles are prized in hardcore off-roading because they move the final gear reduction out to hubs behind each driven wheel. That raises the axle shafts and leaves less hardware hanging below the frame, so a vehicle can run tall tires and clear obstacles that would stop a conventional drivetrain. The drawback is price: a typical set from suppliers such as 74Weld costs about $20,000. Zeph Gage’s Jeep XJ project takes a different route, applying a single portal axle to the rear for roughly one-fifth of that cost.
The build is not a bolt-on kit. It combines a Ford 9-inch axle housing, geared hubs sourced from a Humvee and HMMWV portal adapters from Jesse Haines Fabrication. The result is a rear assembly intended to raise the driveline, preserve suspension travel and keep the rear end from hanging up on obstacles that the front can steer around.
A reversed gearset and a flipped differential
A two-gear portal like the Humvee unit takes the rotation of the input shaft and reverses it. That is a simple description of the hardware, but it creates a packaging problem for a conventional axle: the differential and driveline have to work in the correct direction. Gage solved that by flipping the Ford 9-inch differential upside down. A Yukon Gear and Axle third member is then bolted to the diff, effectively creating a budget high-pinion arrangement from low-pinion parts.
The payoff is not only height. The layout is said to add six inches of clearance while retaining full shock travel, a combination that can be difficult with portal axles. It is also intended to reduce stress on the differential itself. Those are design claims for this build rather than results from an independent durability program, but they explain why the flipped-differential approach is more than a novelty.
Why a rear-only portal can make sense
Installing a portal only at the rear may look like an incomplete upgrade, but it follows a practice used in the remote-control rock-crawler scene. Keeping the front solid axle avoids the packaging constraints that often appear when portal axles are added to a vehicle that never had them from the factory. Gage therefore does not have to restrict shock travel to make room for front portal hardware, and the ride height does not rise to the extreme levels that a four-corner portal conversion can produce.
The tradeoff is that the rear axle now has a different final-drive arrangement from the front. The gearing has to be matched so the two ends of the vehicle work together, and the build video covers how Gage handled that. The rear-only layout also means the front end keeps its conventional clearance, so the conversion is aimed at a specific problem: the rear differential dragging on ledges or obstacles that the front tires can already clear.
Fabrication is where the budget comes from
Gage’s build relies on considerable custom work. It uses homemade brackets and custom-tapped plates, along with a two-piece brake rotor paired to a Ford Fusion caliper. The Fusion hardware was chosen partly because it offers an integrated electric emergency-brake solenoid and partly for clearance. Those details matter because they show where the cost advantage comes from: the saving is not a cheaper catalog kit but the use of adapted components and fabrication.
The finished Jeep XJ can drive over a five-gallon bucket and still have several inches of spare clearance. That capability is the practical case for the rear-only portal: the rear end is less likely to catch on an obstacle that the front end can steer around. The build is intended to be effectively bulletproof, though that remains a design expectation rather than a demonstrated test result.
What the build demonstrates
The project is best understood as an exercise in packaging and cost. A conventional portal-axle set is expensive because it requires a complete, engineered assembly for each driven wheel. Gage’s approach uses a familiar axle housing, military-derived geared hubs and adapters, then corrects the rotation direction by turning the differential upside down. The result adds clearance without pushing the ride height to an extreme and without giving up rear shock travel.
It is also a one-off. The build does not describe a production kit, a warranty or a durability test, and the custom brackets and brake solution would need to be replicated carefully. That limits how directly the build can be copied by other owners. Still, it demonstrates a useful principle: when a full portal-axle set is out of reach, the rear axle alone can address a specific off-road weakness if the gearing, packaging and fabrication are handled together.
